2N2219 DATASHEET PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Meztizragore Arashimuro
Country: Greece
Language: English (Spanish)
Genre: Education
Published (Last): 3 April 2014
Pages: 296
PDF File Size: 9.10 Mb
ePub File Size: 1.87 Mb
ISBN: 438-8-14006-402-9
Downloads: 45046
Price: Free* [*Free Regsitration Required]
Uploader: Dailabar

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

Here lets us assume the load here consumes around mA maximum so our collector current I C mA. Another important thing to keep in mind, while using a transistor as switch is the base resistor.

2N2219 Datasheet, Equivalent, Cross Reference Search

Where h FE, is the current gain of the transistor which in our case is Current Drains out datasheeg emitter, normally connected to ground. Amplifier modules like Audio amplifiers, signal Amplifier etc.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:.

  ASTM A478 PDF

Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

2N Datasheet pdf – Leaded Small Signal Transistor General Purpose – Central Semiconductor

Current flows in through collector, normally connected to load. As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

In our case for a collector current of mA we have to pass a base current of 16mA. The 2N is a NPN transistor and is normally used as a switch in many circuits. TL — Programmable Reference Voltage.

2N Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

So the value if R B will be. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: This resistor is connected to the base pin of the transistor to limit the current flowing through the base. Submitted by admin on 21 June 2n221 if you looking for an NPN transistor that could switch loads fatasheet for decent amplification then 2N might the right choice for your project.

  CISCO PPDIOO PDF

Complete Technical Details can be found at the datasheet given at the end of this page. This stage is called Saturation Region.

But this calculation will lead to the closest value to start with. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below.

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around datadheet. The value of this current can be calculated by the required amount of current that will be consumed by the load.

So to calculate the resistor value of the base we can use the formulae. Overall it is datasheeg another small signal transistor which is commonly used in switching and amplifying circuits.